Rich electric INVERTEK L series Bedienungsanleitung

INVERTEK® SUNSTAR MPPT SERIES SOLAR CHARGE CONTROLLER SS-50C / SS-80C / SS-80CX / SS-160CX MPPT Installation and Operation Manual 利 佳 興 業

1-1Chapter 1 Installation 1.1 Loads Requirement The SunStar MPPT series plays a major role in planning your PV system. The first step in plannin

1-21.5 Shunt (BCS) The Shunt is an optional component and it is required for the SunStar MPPT to achieve to the optimal operation levels and it funct

1-3 Fig-4

1-41.9 Installation Steps Example: SS-80C MPPT Before starting the SS-80C, keep the breakers, controllers in OFF position. 1. Locate the battery

2-1Chapter 2 Wiring 2.1 Front Panel Display 8 Push Buttons Push buttons Name Description PB1 Data write-in key PB2 UP k

2-2PB4 Reset key to reset the fault. ESC key to return to the last selection level. PB5 Quick function key to the Main Menu: Data Log PB6 Quick fu

2-32.2 Control Terminal Connection Fig-4 Connections Details A BVS- Connecting terminal to Battery Voltage feedback Neg

2-4J MA1 Connecting terminal for the contact A of auxiliary 1 K MC1 Connecting terminal for the common contact of auxiliary 1 L MB1 Connecting

2-52.3 Parallel Connection The parallel connection of SunStar MPPT series can be up to 16 units (1 Master and 15 Slaves) and in the parallel system,

3-1 Chapter 3 User Constants 3.1 The following is the structure of user constants. GROUP CONSTANTSMENU Operation IN =xxx.xV xxx.xAmps

IICONTENTS Introduction ...

3-2 3. 2 The following is the “Initialization Stage Flow Chart”.

3-3 SAVE: If SAVE is selected by pressing key, the controller will save the entered settings and operate with them RCLL (RECALL): Pressing

3-4 3.3 The following is the “Operation Stage Flow Chart”. Main Menu Main Menu-Operation Menu Constants

3-5 Main Menu-Initialize Menu Constants Constants Edit Data Enter Main Menu-Programming Group B Menu

3-6 Main Menu-Programming Group C Menu Group Constants Constants Edit Data Enter Main Menu-Programming Group D, D-

3-7 Main Menu-Programming Group D, Auxiliary 1 ON/OFF Condition Setting Menu Group Constants Constants Edit Data En

3-8 Main Menu-Programming Group E, Auxiliary 2 ON/OFF Condition Setting Menu Group Constants Constants Edit Data

3-9 Main Menu-Programming Group F Menu Group Constants Constants Edit Data Enter

3-10 Main Menu-Programming Group O Menu Group Constants Constants Edit Data Enter

3-11 Main Menu-Data Log Menu Constants Constants Edit Data Enter

III G Group: Data Log...4-5 Chapter 5 Progra

4-1Chapter 4 Constant List Main Menu Group Constant LCD Display Range Unit Factory Setting Remark PageU-00 IN OUT =xxx.xV xxx.xAmps =xxx.xV xxx.

4-2 Main Menu Group Constant LCD Display Range Unit Factory Setting Remark PageB-05 BAT. MAX Charge Amps 0~80/0~160 1A ─ NOTE 6 5-6 FLOOD- ED

4-3 Main Menu Group Constant LCD Display Range Unit Factory Setting Remark PageAuxiliary Relay 1 D-01 Set Aux Relay 1 Mode OFF, ON, Solar Volta

4-4 Main Menu Group Constant LCD Display Range Unit Factory Setting Remark PageWhen D-01=SunStar Time 00~23 Hr 00~59 Min 1 Min 0 5-11D-03 Wh

4-5 Main Menu Group Constant LCD Display Range Unit Factory Setting Remark PageWhen E-01=OUT Current 0~80/0~160 1A 0 5-12When E-01=BATT Cu

4-6 Data Log G G-09 Clear Energy Harvest Today’s Data Logged Data ─ Today’s Data 5-16 NOTE 1 (U-12, U-13, U-14, U-15) Battery SOC, Battery Curren

4-7NOTE 3 (B-09, B-10, B-11, B-12) These constants are only displayed if Flooded is selected as battery type (B-02). NOTE 4 (C-02, C-03, C-04, C-05)

5-1 Chapter 5 Programming Constants *** Main Menu*** Operation U-00: IN=xxx.xV xxx.xAmps OUT=xxx.xV xxx.xAmps z Use Constant U-00 to monitor

5-2 U-07: EnergyHarvest Today 2 z This screen displays how much time the charger was in Float mode “Today” in Hour:Minute. U-08: Stage of Charge

5-3 and will only be active when using an optional 50mv/500amp external shunt. ※ U-13 will only be displayed when the terminal BVS (Battery Voltage

IVIntroduction The SunStar MPPT is a highly reliable solar battery charger and its most critical feature is to maximize the harvest energy from the P

5-4 *** Main Menu*** Initialize A-01: Access Level z Use Constant A-01 to select the user constant access level. This level determines which use

5-5 4. Go to any display of A-xx and press DOWN key and hold it, then press ESC key at the same time till A-04 constant occurs. 5. Enter the desire

5-6 B-04: Set Battery Capacity z This setting controls battery charging amperages and other settings. The factory setting for CAPACITY is 1600 amp

5-7 B-07: Set Absorption Time z Use Constant B-07 to adjust the length of Absorption time. The factory setting is 2 hours (displayed as 02:00). B-

5-8 B-11: Set Days Between EQU z This constant is only displayed if Flooded is selected as battery type (B-02). Use Constant B-11 to select the

5-9 Type (C-01). z The scan frequency is settable from 1 minute to 4 hours and the factory setting is 1 hour. Press the UP and DOWN key to increas

5-10functions will be added in the future. z Use Constant D-01 to select the Auxiliary Relay 1 mode and what it is based on. z Auxiliary Relay 1

5-11When D-01=SunStar Time < or > 00~23 Hr 00~59 Min 1 Min When D-01=Battery SOC < or > 0~100% 1% ※ Battery SOC is only active whe

5-12 D-04: Aux RY1 MIN. ON time z Use Constant D-04 is to set the minimum time that the relay can remain active. z The minimum time is set to av

5-13F-02: SunStarParallel Addr z A SUNSTAR MPPT assigned as Master or Standalone is always addressed 01 automatically so the address assignment in

Vbatteries; 2/3/4-stage charging with adjustable set points for all parameters. z Wire the PV modules in series up to 112VDC normal (140VDC Max) for

5-14consumes a fair amount of quiescent current, it is recommended that the on time be as short as possible. z Press ENTER key to enter the setting

5-15charging, reduce loads, or expand the PV array to ensure that batteries are fully recharged. For maximum service life batteries should be fully r

5-16G-09: Clear Energy Harvest z Use Constant G-09 to clear Today’s Data or all the Logged Data. z Press ENTER key and use UP and DOWN keys to sel

6-1Chapter 6 Trouble Shooting z Proceed as follows for a quick detection of common faults. z Consult your Rich Electric dealer if the fault cannot

VISpecification Model No. SS-50C MPPT SS-80C MPPT SS-80CX MPPT SS-160CX MPPTMaximum output current (Continuous at up 50℃ ambient temperature) 50

VIIDimension for SS-50C MPPT Unit: mm Fig-1

VIIIDimension for SS-80C MPPT Dimension for SS-80CX MPPT Unit: mm Fig-2

IXDimension for SS-160CX MPPT Unit: mm Fig-3